Analysis and Solution of Common Defects in Coil Winding Machine
Analysis and Solution of Common Defects in Coil Winding Machine
one. Bad salt bath:
1. Poor enameled wire: Take out part of the enameled wire from the wire barrel (stretch a few times) and put it in salt water to judge.
2. Poor tension of the winding machine (too large): The rotor wire package placed in salt water bubbles irregularly, and the value rises slowly. (Too small): The wire is easy to hang on the steel sheet during the winding process and the wire package is large and loose.
Solution: The enameled wire passing through the tension system of the winding machine must be checked with a spring balance on the tension meter before winding.
3. Wool felting carbon. Damage to the winding wheel of each winding machine. Damage to the small bearing of each winding: The rotor wire package placed in salt water bubbling irregularly, and the value rises faster.
Solution: Replace the damaged wool felt, thread roller, and small bearing
4. Damage to the winding mold of the winding machine (wire mold): The rotor wire package placed in salt water bubbles regularly, and the bubble position is in the upper, lower or middle of the iron core (each slot is in the same position). The value rises quickly.
(Hook wire set): The rotor wire put in the salt water bubbling on the neck (the damage part should be visible).
Solution: Check the mold. Determine the position. Grind and polish.
5. Poor debugging of the winding machine caused the indexing change during the winding process (and even scratches on the bottom of the enameled wire): the winding mold of the winding machine was not adjusted well at the center of the hook sleeve, and the balance of the winding mold was not adjusted properly. Hook thread set
The position of the winding machine is not adjusted properly (one side is high and the other is low), the parallel cylinder movement is not coordinated (one side is fast and the other is slow), the bearing in the indexing shaft of the winding machine is defective, and the flat bearing in the clamping mechanism is defective.
The rotor wire package put in the salt water bubbles regularly (several slots are in the same position, especially the last two sets of coils).
Others: the fly fork bearing is broken, the fly fork spindle bearing gear is worn, and the fly fork pulley bearing gear is worn, which causes the mold center to be poorly adjusted.
Solution: Check and debug the above problem points, check and replace each bearing.
Note: When changing the enameled wire, check whether there is any burrs around the wire stabbing.
6. The threading method is incorrect: there are too many turns of the copper wire on the winding wheel of the electromechanical control magnetic powder tensioner or the auxiliary winding wheel, and the magnetic powder tensioner usually takes 2-3 turns. The supplement is 1 lap. (The enameled wire will squeeze each other under the action of resistance and tension, and the paint film will be damaged). The enameled wire is threaded on the thread-passing wheel protection rod, the thread-passing wheel position at the thread inlet of the main shaft is not correct (the thread directly rubs against the thread-passing wheel protection rod), the nylon tube in the main shaft falls off, and the spindle reaches
The flying fork line does not pass the reel.
Solution: Check the above problems and adjust.
7. Poor winding mold of the winding machine: The winding mold of the winding machine is severely worn after long-term grinding and polishing, and it rarely protects the steel sheet even when the enameled wire is scraped off the steel sheet. The gap between the side guard plate and the middle guard plate of the winding mold is too small (for lines above 0.45), the position of the middle guard plate is not adjusted properly, the steel sheet is scraped off the wire, the salt bath is bad or the wire is broken.
Solution: Check the mold, process, and debug carefully.
two. Missing hook:
1. Poor tension setting of the winding machine: the thread can be seen to be loose when hooking. The wire at the hook of the wound rotor is not tightened (when hooking, the spring on the tension mechanism pulls the magnetic powder tensioner until the enameled wire at the hook is tightened before it can be hooked. When the tension setting is not good, the magnetic powder tensioner cannot lock the enameled wire directly from the wire. Pull out from the tube, leaking hook), a lot of continuous hooks and leaking hooks.
Solution: Adjust the tension setting. (If the value is too small, the hook will be missed, and the thread will not hang at the bottom of the hook, and the hook will be loose. If the value is too large, the enameled wire will be cut by the sharp angle of the hook and scratched)
2. The spring on the tension mechanism of the winding machine is not suitable for use: the wire is loose when the spring force is small, and the wire is not hooked at the bottom of the hook and easily loosened. The thread is easy
Related Post
REPOSAL? releases layer-wound high-voltage package full-automatic interlayer insulation winding machine
REPOSAL? releases layer-wound high-voltage package full-automatic interlayer insulation winding machine
Suzhou Xiepu Electronic Machinery Equipment Co., Ltd. successfully released the SP-D102M7 model of layer-wound high-voltage package automatic interlayer insulation winding machine-this model greatly improves the winding efficiency of layer-wound high-voltage package coils, and the coil is consistent Sex. The REPOSAL? winding machine reduces the winding cost of the layer-wound high-voltage package. In the new model, it has added a compact insulation belt automatic cutting mechanism, and high-quality solutions such as dynamic balance performance after multiple skeletons are wound.
Enclosed rectangular transformer winding machine-thin wire reciprocating
Enclosed rectangular transformer coil with a thin diameter of 0.12mm, which requires fast winding speed and convenient product loading and unloading.
Precise winding of self-adhesive coil with skeleton
As shown in the figure below, it is a sensor coil used in the medical industry. The skeleton is made of aluminum. The diameter of the enameled wire is 0.1mm. The customer requires the arrangement to be neat and free of winding defects. The company has carefully evaluated the specific requirements of the customer, because the winding process and winding are considered. After the completion of the structure, the self-adhesive enameled wire process was adopted, and the self-adhesive coil winding machine was further optimized. The project was successfully completed. At the same time, some experience was summarized and shared with the public during the process.
In recent years, due to self-adhesive support, self-adhesive coils do not need to be dipped in the later stage, which is convenient for industrialization. They have been widely used in deflection coils of precision instruments, combined coils in micro motors, and micro coils in sensors.
Fiber Optic Gyro Winding Machine-REPOSAL? Winding Machine Official Website
Compared with mechanical gyroscopes, fiber optic gyroscopes have no moving parts, impact resistance, high sensitivity, and long life. Therefore, fiber optic gyroscopes are widely used in high-precision and high-speed positioning scenarios and will gradually replace electromechanical gyroscopes.
The basic components of the fiber optic gyroscope are the optical path and the circuit, and the fiber is the core component of the gyroscope. The fiber winding machine for preparing high-precision fiber coils has also become the key point of the gyroscope.
However, due to the blockade of its related technologies, the fiber optic gyro winding machine has always been a key technology insurmountable. REPOSAL? Electronic Machinery Co., Ltd. actively develops fiber optic gyro winding machines in response to market demand.
Through continuous research and improvement, we automate the winding process of the fiber optic gyroscope, and compare and analyze the winding methods of various fiber coils. We have obtained that the tension control and the accuracy of the winding during the fiber winding process affect the structure of the wound fiber coil. The key factor.
By optimizing the aforementioned tension control factors and winding accuracy algorithm, the effective and stable control of reasonable tension, the effective and reliable high-precision winding control, the memory of all process parameters, and the convenience of control, a new generation of optical fiber winding machine was developed and put into production .
With the practical application of research and development results, we will continue to improve and produce high-reliability and high-efficiency fiber optic gyro winding machines.
REPOSAL winding machine continuous innovation to consolidate brand value
Suzhou REPOSAL Electronic Mechanical Equipment Co., Ltd. is a technology enterprise specializing in R&D and production of winding equipment. For many years, it has insisted on maintaining innovation and researching and developing products with independent intellectual property rights.
For quite a long time, my country's winding machine manufacturing industry generally has the problems of low technology, small scale, free and scattered production, and insufficient technological innovation of most enterprises. Compared with related industries abroad, my country currently has fewer types of winding machines and supporting equipment. The control technology used is relatively backward, and its accuracy and performance are not as good as those of their European and American counterparts. Moreover, the product has low production capacity and poor stability.
In the face of technical gaps, Suzhou REPOSAL made a detailed market research and took the entire series of precision winding machines and Roche coil winding machines as breakthrough points.It valued cooperation with user companies and not only carefully understood the existing process requirements of customers. And through the company's accumulated technical database for many years, on the premise of no or little increase in costs, it actively provides new ideas and new solutions for customer process upgrades.In a specific single implementation case, this approach has undoubtedly aggravated us The execution cost of the company has reduced the company's profits, but this idea has been implemented and verified for a long time.In fact, our customers have tapped the potential of the coil winding process through our winding machine equipment and become our long-term cooperative customers. We have also accumulated more technical data for our research and development direction and solutions through proactive improvement of individual cases, so as to achieve continuous innovation.